Limonite (brown iron ore) used as a raw material for sintering is inexpensive, but problems include the fact that this ore combines strongly with water and has a coarse particle size. These properties have a serious impact on productivity in the sintering process (Lu and Ishiyama 2016). By solving these problems, this device makes it possible ...
The sintering process is shown in Fig. 3. In sintering process, the iron ore, flux, fuel and auxiliary materials are fed into the sintering machine after batching and mixing. Their dosages per ton sinter are m ore, m flux, m fuel and m other, respectively. The energy values of them are e ore, e flux, e fuel and e other, respectively. After ...
References (69) ... 6,7) Iron ore sintering is an agglomeration process of a mixture of ore fines mainly consisting of iron ores, fluxes and fuel, which produces sinters with suitable chemical and ...
In the sintering process, iron ores are usually blended and mixed with fluxing materials,, limestone and burnt lime, and fuels (socalled agglomeration agents),, coke, anthracite, and some recycle dusts.
The iron and steel industry has made an important contribution to China's economic development, and sinter accounts for 7080% of the blast furnace feed charge. However, the average grade of domestic iron ore is low, and imported iron ore is easily affected by transportation and price. The intelligent ore blending model with an intelligent algorithm as the core is studied.
Experimental Materials. As shown in Group 1 of Table 1, the experimental raw materials were from a steel sintering workshop in Tangshan, the basicity of the sintering mixture was, the content of MgO was %, the Al 2 O 3 content was %, and more than 80% the fuel particle size is larger than 3 mm.
The evaluation model of iron ore properties was established based on the high temperature characteristic numbers with employing fuzzy mathematics. Then, with the constraint of sinter properties and the raw materials, the ore blending model was built, whose target was to obtain the lowest cost and the best sinter properties.
The best sintering maximum temperature is between 1300 and 1400 °C, where sinter ore with high quality can be obtained. ... The sintering process of iron ore accounts for about 10, 40 and 70% of ...
Mineralization testing process included ore matching, agglomeration, roasting and mineralogical analysis. Iron ores and fluxes (dolomite, limestone, and quicklime) were mixed to a feed, which then was used to produce sinter with SiO 2 %, basicity (CaO/SiO 2) and MgO %, the proportions of each material were shown in Table principle of ore matching for adhesion layer was ...
ABSTRACT. Sintering is an agglomeration process that fuses iron ore fines, fluxes, recycled products, slagforming elements and coke. The purpose of sintering is to obtain a product with suitable composition, quality and granulometry to be used as burden material in the blast furnace.
The production of crude steel in the iron and steel industry in China has grown dramatically, which has made the country the world's largest steel producer since 1996 1,2,3. 40%60% of the total ...
Therefore, the carbon and Cl content of the raw materials used for iron ore sintering are important to the formation of dioxins. This is supported by Kawaguchi et al. (2002c), who reported that the properties and contents of the solid fuels and chlorides in the raw mixture significantly affect dioxin emissions during the iron ore sintering process.
Sintering raw materials include iron ore powder (rich ore powder, concentrate powder), flux (limestone, dolomite, quicklime, etc.), fuel (coke powder and anthracite), additives (roll scale and some recycled materials), return ore in sintering process, and return ore below ironmaking trough. Process Flow
I. RuizBustinza of Mining and Energy Engineers (UPM) J. Mochón Carmen GonzálezGasca European University of Madrid Abstract and Figures Sintering is an agglomeration process that fuses...
Iron ore mineral: The gratekiln is best suited for magnetite and magnetite/hematite mixtures, while the straight grate is suitable for all types of feed ... The pelletizing process involves the preparation of raw materials; the proportioning and mixing of raw materials; the formation, preheating, and firing of green balls; and the cooling of ...
To reduce the raw material cost of the blast furnace ironmaking system and realize the collaborative optimization of the whole process from iron ore procurement to blast furnace ironmaking, He et al. [15] developed a whole system and whole process optimized sintering batching platform for blast furnace ironmaking.
Iron ore sintering was a hightemperature process that preparing lump burden for further ironmaking. During this process, iron ore fines, recycled ironbearing materials, fluxes, and solid fuel including coke breeze, anthracite, etc., were thoroughly mixed and then agglomerated into finished sinter under 1300 °C provided by the combustion of ...
According to the Environmental Protection Agency, the sintering process converts finesized raw materials, including iron ore, coke breeze, limestone, mill scale, and flue dust, into an agglomerated product, sinter, of suitable size for charging into the blast furnace.
Iron ore is the source of primary iron for the world's iron and steel industries. It is therefore essential for the production of steel, which in turn is essential to maintain a strong industrial base. Almost all (98%) iron ore is used in steelmaking. Iron ore is mined in about 50 countries. The seven largest of these producing countries ...
The typical iron ore sintering process supplies the main ferrous charge for blast furnaces in most steel mills. During sintering, first the sinter raw materials are intimately mixed and granulated to produce granules with a narrow size distribution, large mean size and sufficient strength. ... while sinter is the best candidate material for ...
The CaO and MgO slag components do not coexist with iron ores and are added separately; therefore, CaO (such as limestone) and MgO (such as serpentine or dolomite) are mixed with iron ore fines as the sinter raw mix for the sintering process. The ultrafine iron ore reacts with the fluxes and forms a bonding matrix (silicoferrite of calcium and ...
Iron ore sinter plants are energyintensive components of integrated iron and steel production (see Table 1), where the iron ore fines (<5 mm) are converted into larger (>5 mm) lump sinter cakes with greater gas permeability, which are the most important burden materials for iron making in blast furnaces (BFs) [7].The main process is shown in Fig. 2 and described in detail in previous studies ...
In iron making process, sintering of iron ore fines is an integral step to utilize not only the ore fines but also to introduce a part of flux (limestone and dolomite) along with the sinter in blast furnace burden. In this way, the productivity of the furnace considerably improves.
The sintering process can be defined as a thermal agglomeration process that is applied to a mixture of iron ore fines, recycled ironmaking products, fluxes, slagforming agents, and solid fuel (coke) with the objective of obtaining a product with the suitable characteristics (thermal, mechanical, physical, and chemical) to be fed to the blast furnace.
© DZCrusher - كل الحقوق محفوظة
