JSW Steel sinter plant receives iron ore fines of 10 mm size from Bellary Hospet region which consist of 3 to 9% bigger than 10 mm and 30 to 35% smaller than mm size fraction. It is well known that larger particles favour diffusion bonding and smaller particles favour slag bonding in sintering process.
An iron ore blend was prepared by mixing the iron ore nes with the required proportion of pellet nes. A small pile was prepared by layering the iron ore blend, coke breeze, ux and return nes on a weight basis, according to the propor tions mentioned in Table 1. After proper mixing, these raw materials were transferred to the granulation drum.
The present work proposes a novel process to sinter porous iron ore (porosity ~2324%) with enhanced productivity and quality. The iron ore is preprocessed in the presence of calcined lime for the temporary closure of pores, which further prevents water absorption during the granulation process in drum in the presence of water. The calcined lime coated iron ore provides surface coating on ...
Sintering is a thermal agglomeration process that is applied to a mixture of iron ore fines, recycled ironmaking products, fluxes, slagforming agents, and solid fuel (coke). The purpose of the sintering process is manufacturing a product with the suitable characteristics (thermal, mechanical, physical and chemical) to be fed to the blast furnace.
The results show that the start decomposition temperature of #2 iron ore is °C, which is °C higher compared to that of #1 iron ore, because of its smaller pores and the difficulty of ...
Abstract Iron ore, pellets, and sinter were reduced with hydrogen at 800 °C to understand the degree of reduction and the mineralogical aspects. The weight loss of goethite and limonite iron ore was noticed to be lower than that of magnetite and hematite varieties. Xray diffractometry (XRD) indicated 100 pct Fe in the case of hematite, 93 pct in magnetite, 53 pct in goethite, and as low as ...
JSW Steel Limited, Toranagallu 583119, Bellary, Karnataka, India. Search for more papers by this author. Mahapatra, ... The selective granulation process is a new sintering process for high alumina iron ore fines, and can eliminate the adverse effects of 'hard to sinter' or 'unsuitable for ironmaking' ores. ...
Sintering is a complex industrial process that applies heat to fine particles of iron ore and other materials to produce sinter, a solidified porous material used in blast furnaces.
Sintering, which is also called 'frittage,' is the process of forming a solid mass of material through heat and pressure without melting to the point of liquefaction. This process involves the atoms in materials diffusing across the particle boundaries and fusing together into one piece. Sintering occurs naturally in mineral deposits, and ...
The pelletization process is the primary consumer of binders in the iron ore industry. The selection of an appropriate binder type and dosage is of critical importance in producing good quality pellets at a reasonable price. Binders accomplish two very important functions in iron ore pelletization: .
Iron ore sintering is one of the key steps in the ironmaking process, where granulated pellets are transformed into sinter in the sintering machine, providing an ideal raw material for ironmaking blast furnace. Drum granulation in the sintering process plays an essential role in determining the final sintering performance.
This chapter contains sections titled: Introduction Comparison of the Property of Iron Ore before and after Ore Dressing Sintering Ore Blending Optimization Model Model Application and Sinter...
Intensification of the iron ore sintering process was approached by injecting hydrogenrich gas into the sinter bed. The location of the injection was critical to the pyrolysis of the solid fuel, and the SOx and NOx emissions. After installing the injection system in the most appropriate zone, the process intensified, and the emissions were ...
Optimizing iron ore proportion is significant for improving the performances of sintering process, and the cost of iron ores is important for iron and steel company. Linear programming is an effective optimization method, which can consider both the indices of ore proportion and the cost of iron ores at the same time. Therefore, in the present work, aimed for reducing the cost of sintering ...
Lump iron ore, fluxed/superfluxed sinter and acid/basic pellets are the major iron bearing materials. Because of high SiO 2 and Al 2 O 3 content in iron bearing materials, limestone and dolomite as fluxes are added in sintering process to promote the formation of low melting slag which helps in achieving the desired sinter properties.
At present, the alumina content in the sinter grade iron ore fines at JSW Steel varies from 4 to 6%. The quality of iron ore presently being used calls for extensive investigations to produce low ...
Abstract Coke breeze is the most common fuel used in sintering, and its usage depends on the alumina content and fineness of the sinter mix. The coke breeze consumption in the JSW Steel Limited sinter plant was high compared to many other sinter plants in the world, and as there was a local shortage, optimisation in the sinter plants was necessary. FeO is an indicator of the thermal state of ...
The granulation of iron ore is an important process in the iron ore sintering. It strongly affects the permeability of sinter bed and then affects the productivity and properties of produced sinter such as strength and reducibility. The granulation ability of limonite ores was poor; they should be used with high granulation ability iron ores to ...
The abnormal operating mode of the iron ore sintering process will produce sinter ore with low yield and poor quality. It is of high economic value to ensure that the sintering process runs under ...
In the iron ore sintering process, the fine size of mm in the sinter base mix is influencing on the sinter mineralogy and sinter properties. The amount of adhering fine particles to nuclei is strongly influenced by moisture available for granulation. ... JSW Steel has setup Asia's largest beneficiation plant with a designed capacity of ...
Sintering is the most economic and widely used agglomeration process to prepare iron ore fines for blast furnace use. In this chapter, the sintering process is first described and the key steps of the sintering process, namely, granulation and thermal densification, are identified. Discussion is then focused on the effect of the chemical ...
The sintering process can be defined as a thermal agglomeration process that is applied to a mixture of iron ore fines, recycled ironmaking products, fluxes, slagforming agents, and solid fuel (coke) with the objective of obtaining a product with the suitable characteristics (thermal, mechanical, physical, and chemical) to be fed to the blast furnace.
Sintering facilitates feed of iron ore fines in blast furnace, blended with fluxes and coking coal / coke. The depletion of iron ore quality poses new challenges to steel makers. There is a need to find alternate solutions maintaining optimal composition and metallurgical properties of the sinter to enable the production of highquality hot ...
The iron and steel industry has made an important contribution to China's economic development, and sinter accounts for 7080% of the blast furnace feed charge. However, the average grade of domestic iron ore is low, and imported iron ore is easily affected by transportation and price. The intelligent ore blending model with an intelligent algorithm as the core is studied.
Ironbearing byproducts are rich in iron and carbon and are often reused in the iron ore sintering process. However, there are fewer studies on the effect of them on sintering flue gas pollutants.
LD slag contains high amount of CaO, iron, and MgO, thus recycling it through sintering process helps in the saving of flux and iron ore. The recycled wastes have some effect on sinter quality, strength and productivity. JSW Steel Limited is a Mtpa integrated steel plant and produces 2000 to 2500 tons of LD slag per day.
© DZCrusher - كل الحقوق محفوظة
